
Since YKS has shared his cinewhoop 4K with a stunning videography, people are fascinated in 4K whoop. So here we are. A real 4S 4K Beta85X whoop!!! Upgraded F4 V2 FC with BLHeli_32 16A ESC, using single N-channel MosFETs, makes the structure and performance more stable and support 4S power definetly. Mounting with Tarsier 4K camera, great choice for cruising, so you can get tons of fun in this cine whoop.
MAIN FEATURES:
- F4 V2 FC board has added extra 4 pluggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting.
- High performance STM32F405 processor FC boards and tuned Betaflight OMNIBUSF4SD (OBSD). Faster input signals with lower latency and higher update rate are reachable.
- Using single N-channel MosFETs on ESC board which have a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
- Soldering with 25V/220uf electrolytic capacitor, for protecting ESC board, reducing the defective rate caused by the instantaneous high voltage.
- Installed with Caddx Tarsier 4K camera with ND8 fliter which supports APP setting and switchable resolution setting of 4K, 2.7k, 1440P, 1080P.
- Upgraded 1105 motor from 6000KV to 5000KV, with a light weight but definitely will give you extreme power and speed. Motor comes with cable connectors.
- Durable and light enough frame is customized for the Beta85X. To increase its stability, we specially add an extra stiffener brace of carbon fiber. Whole drone no soldering or tinkering necessary.
- 450mAh 4S high rate battery is recommended by default. But pilot could also use their own batteries with battery strap. Optional and affordable.
BETA85X SPECIFICATIONS
Weight: 88.6g (without battery)
F405 V2 Flight Controller and 16A BLHeli_32 ESC
Motors: 1105 5000KV with connector
Props: 2" 4-Blades Props
Camera: CADDX Tarsier 4K
Canopy: Canopy for Tarsier 4K camera
Receiver option: PNP
Recommend battery: 4S 450mAh Battery (Not including)
5.8G FPV antenna
Flight time: 4min - 6min with 450mAh 4S battery
FC SPECIFICATIONS
Find more details about this F405 V2 FC in another page.
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
ESC SPECIFICATIONS
Find more details about this BLHeli 32 ESC board in another page.
Support BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
MCU: STM32F051K66
Camera SPECIFICATIONS
Find more details about this Caddx Tarsier 4K camera in another page.
Weight: 19.5g
FOV: 4KF 2.8, FOV 150°(16/9), FPV FOV 165°(4/3)
Lens: Dual lens 2.8 / 12Mega
Image Sensor: 12M SONY sensor
TV System: NTSC / PAL, can be changed
Anti-Shake: Hardware anti-shake
Scene Mode: Auto / Personage / Scenery / Defog
Recording Timing Larm: OFF / 1mins / 3mins / 5mins / 10mins
Horizontal Resolution: 1200TVL
Image: 16:9 / 4: 3 (changeable)
Camera OSD: Seperate OSD
The camera tilt angle is switchable from 20 degree to 30 degree with ND8 fliter.
1 * Beta85X 4K Whoop Quadcopter(4S) PNP
1 * ND8 Filter for Tarsier 4K camera
1 * OSD Menu Board
COMPARISON
Write your review
You must be logged in to post a review.
Description
Since YKS has shared his cinewhoop 4K with a stunning videography, people are fascinated in 4K whoop. So here we are. A real 4S 4K Beta85X whoop!!! Upgraded F4 V2 FC with BLHeli_32 16A ESC, using single N-channel MosFETs, makes the structure and performance more stable and support 4S power definetly. Mounting with Tarsier 4K camera, great choice for cruising, so you can get tons of fun in this cine whoop.
MAIN FEATURES:
- F4 V2 FC board has added extra 4 pluggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting.
- High performance STM32F405 processor FC boards and tuned Betaflight OMNIBUSF4SD (OBSD). Faster input signals with lower latency and higher update rate are reachable.
- Using single N-channel MosFETs on ESC board which have a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
- Soldering with 25V/220uf electrolytic capacitor, for protecting ESC board, reducing the defective rate caused by the instantaneous high voltage.
- Installed with Caddx Tarsier 4K camera with ND8 fliter which supports APP setting and switchable resolution setting of 4K, 2.7k, 1440P, 1080P.
- Upgraded 1105 motor from 6000KV to 5000KV, with a light weight but definitely will give you extreme power and speed. Motor comes with cable connectors.
- Durable and light enough frame is customized for the Beta85X. To increase its stability, we specially add an extra stiffener brace of carbon fiber. Whole drone no soldering or tinkering necessary.
- 450mAh 4S high rate battery is recommended by default. But pilot could also use their own batteries with battery strap. Optional and affordable.
Specification
BETA85X SPECIFICATIONS
Weight: 88.6g (without battery)
F405 V2 Flight Controller and 16A BLHeli_32 ESC
Motors: 1105 5000KV with connector
Props: 2" 4-Blades Props
Camera: CADDX Tarsier 4K
Canopy: Canopy for Tarsier 4K camera
Receiver option: PNP
Recommend battery: 4S 450mAh Battery (Not including)
5.8G FPV antenna
Flight time: 4min - 6min with 450mAh 4S battery
FC SPECIFICATIONS
Find more details about this F405 V2 FC in another page.
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
ESC SPECIFICATIONS
Find more details about this BLHeli 32 ESC board in another page.
Support BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
MCU: STM32F051K66
Camera SPECIFICATIONS
Find more details about this Caddx Tarsier 4K camera in another page.
Weight: 19.5g
FOV: 4KF 2.8, FOV 150°(16/9), FPV FOV 165°(4/3)
Lens: Dual lens 2.8 / 12Mega
Image Sensor: 12M SONY sensor
TV System: NTSC / PAL, can be changed
Anti-Shake: Hardware anti-shake
Scene Mode: Auto / Personage / Scenery / Defog
Recording Timing Larm: OFF / 1mins / 3mins / 5mins / 10mins
Horizontal Resolution: 1200TVL
Image: 16:9 / 4: 3 (changeable)
Camera OSD: Seperate OSD
The camera tilt angle is switchable from 20 degree to 30 degree with ND8 fliter.
In The Box
1 * Beta85X 4K Whoop Quadcopter(4S) PNP
1 * ND8 Filter for Tarsier 4K camera
1 * OSD Menu Board
Videos
FAQ
COMPARISON
Downloads
Reviews
Write your review
You must be logged in to post a review.