Since YKS has shared his cinewhoop 4K with a stunning videography, people are fascinated in 4K whoop. So here we are. A real 4S HD Beta85X whoop!!! Upgraded F4 V2 FC with BLHeli_32 16A ESC, using single N-channel MosFETs, makes the structure and performance more stable and support 4S power definitely. Mounting with Caddx Turtle V2 camera, great choice for cruising, so you can get tons of fun in this cine whoop.
MAIN FEATURES:
- F4 V2 FC board has added extra 4 pluggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting.
- High performance STM32F405 processor FC boards and tuned Betaflight OMNIBUSF4SD (OBSD). Faster input signals with lower latency and higher update rate are reachable.
- Using single N-channel MosFETs on ESC board which have a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
- Soldering with 25V/220uf electrolytic capacitor, for protecting ESC board, reducing the defective rate caused by the instantaneous high voltage.
- Installed with Caddx Turtle V2 1080P camera
- Upgraded 1105 motor from 6000KV to 5000KV, with a light weight but definitely will give you extreme power and speed. Motor comes with cable connectors.
- Durable and light enough frame is customized for the Beta85X. To increase its stability, we specially add an extra stiffener brace of carbon fiber. Whole drone no soldering or tinkering necessary.
- 450mAh 4S high rate battery is recommended by default. But pilot could also use their own batteries with battery strap. Optional and affordable.
BETA85X SPECIFICATIONS
Weight: 80.5g (without battery)
F405 V2 Flight Controller and 16A BLHeli_32 ESC
Motors: 1105 5000KV with connector
Props: 2" 4-Blades Props
Camera: CADDX Turtle V2
Canopy: Canopy for Turtle V2 camera
Receiver option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky / TBS Crossfire / PNP
Recommend battery: 4S 450mAh Battery (Not including)
5.8G FPV antenna
Flight time: 4min - 6min with 450mAh 4S battery
FC SPECIFICATIONS
Find more details about this F405 V2 FC in another page.
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
ESC SPECIFICATIONS
Find more details about this BLHeli 32 ESC board in another page.
Support BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
MCU: STM32F051K66
Camera and V02 VTX SPECIFICATIONS
Find more details about this Caddx Turtle V2 camera in this page.
The primary purpose of the Beta85X drone is for a cinematic whoop drone. Many polits revamp their Beta75X to HD whoop drone--They add a HD DVR camera on Beta75X drone to get high defination and beautiful flying footage and video. Inspired by this, we want to provide a BNF whoop drone with HD DVR camera by default so that pilot do not need to assemble it by hand and also get more power on punch for acro mode.
Output power: 25mW and 200mW (Adjustable)
Smart Audio function is included for radio control
Antenna: Customized ZRC antenna
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Caddx Turtle V2 Camera
TV System: NTSC
Field of view: 100-120 degrees with 1/3 lens
1 * Beta85X HD Whoop Quadcopter(4S) PNP
1 * OSD Menu Board
COMPARISON
Write your review
You must be logged in to post a review.
Description
Since YKS has shared his cinewhoop 4K with a stunning videography, people are fascinated in 4K whoop. So here we are. A real 4S HD Beta85X whoop!!! Upgraded F4 V2 FC with BLHeli_32 16A ESC, using single N-channel MosFETs, makes the structure and performance more stable and support 4S power definitely. Mounting with Caddx Turtle V2 camera, great choice for cruising, so you can get tons of fun in this cine whoop.
MAIN FEATURES:
- F4 V2 FC board has added extra 4 pluggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting.
- High performance STM32F405 processor FC boards and tuned Betaflight OMNIBUSF4SD (OBSD). Faster input signals with lower latency and higher update rate are reachable.
- Using single N-channel MosFETs on ESC board which have a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board.
- Soldering with 25V/220uf electrolytic capacitor, for protecting ESC board, reducing the defective rate caused by the instantaneous high voltage.
- Installed with Caddx Turtle V2 1080P camera
- Upgraded 1105 motor from 6000KV to 5000KV, with a light weight but definitely will give you extreme power and speed. Motor comes with cable connectors.
- Durable and light enough frame is customized for the Beta85X. To increase its stability, we specially add an extra stiffener brace of carbon fiber. Whole drone no soldering or tinkering necessary.
- 450mAh 4S high rate battery is recommended by default. But pilot could also use their own batteries with battery strap. Optional and affordable.
Specification
BETA85X SPECIFICATIONS
Weight: 80.5g (without battery)
F405 V2 Flight Controller and 16A BLHeli_32 ESC
Motors: 1105 5000KV with connector
Props: 2" 4-Blades Props
Camera: CADDX Turtle V2
Canopy: Canopy for Turtle V2 camera
Receiver option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky / TBS Crossfire / PNP
Recommend battery: 4S 450mAh Battery (Not including)
5.8G FPV antenna
Flight time: 4min - 6min with 450mAh 4S battery
FC SPECIFICATIONS
Find more details about this F405 V2 FC in another page.
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
ESC SPECIFICATIONS
Find more details about this BLHeli 32 ESC board in another page.
Support BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200
Input voltage: 3-4S lipo
Cotinue current: 16A
Peak current: 19A
Firmware target: BETAFPV-16A-32bit
MCU: STM32F051K66
Camera and V02 VTX SPECIFICATIONS
Find more details about this Caddx Turtle V2 camera in this page.
The primary purpose of the Beta85X drone is for a cinematic whoop drone. Many polits revamp their Beta75X to HD whoop drone--They add a HD DVR camera on Beta75X drone to get high defination and beautiful flying footage and video. Inspired by this, we want to provide a BNF whoop drone with HD DVR camera by default so that pilot do not need to assemble it by hand and also get more power on punch for acro mode.
Output power: 25mW and 200mW (Adjustable)
Smart Audio function is included for radio control
Antenna: Customized ZRC antenna
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
Caddx Turtle V2 Camera
TV System: NTSC
Field of view: 100-120 degrees with 1/3 lens
In The Box
1 * Beta85X HD Whoop Quadcopter(4S) PNP
1 * OSD Menu Board
Videos
FAQ
COMPARISON
Downloads
Reviews
Write your review
You must be logged in to post a review.