
The new layout 12A 2-4S F4 AIO FC(BLHeli_S) is customized for Toothpick Drone. With the real holes, side-mount USB and all solder pads of the edge of FC, greatly reducing installation time and improving ease of self-assembly. The weight saving of the all in one board makes this ideal for tight builds - using the included Anti-vibration rubber dampers for mini stack height.
BULLET POINT
- New layout with whoop mounting pattern, designed real holes instead of notches, customized for Toothpick Drone
- Adopt USB side-mount, easy to plug in
- All of solder pads are at the edge of FC, which is a convenience to solder
- Double-sided motor solder pad. Pins pad and wires pad are both built-in for motors connection
- Integrated with a Betaflight MATEKF411RX processor FC, Betaflight OSD and 2-4S 12A ESC, support 4S battery for fast-flying experience
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 (100MHZ)
Six-Axis: MPU6000 (SPI connection)
Size: 32.5*32.5mm (26.5mm mounting holes)
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Build-in BetaFlight OSD (OSD chip: AT7456E)
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver.
Support programmable LED like WS2812 etc
Built-in current sensor
Weight: 6.2g(Without Pins), 6.5g(Pins Pre-solder)
SPECIFICATIONS OF ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 15A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G-C
Motor Connectors: 1.25mm header pins connector
Factory firmware: G-H-30-16.7
1 * Toothpick F4 2S - 4S AIO 12A brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
Write your review
You must be logged in to post a review.
Description
The new layout 12A 2-4S F4 AIO FC(BLHeli_S) is customized for Toothpick Drone. With the real holes, side-mount USB and all solder pads of the edge of FC, greatly reducing installation time and improving ease of self-assembly. The weight saving of the all in one board makes this ideal for tight builds - using the included Anti-vibration rubber dampers for mini stack height.
BULLET POINT
- New layout with whoop mounting pattern, designed real holes instead of notches, customized for Toothpick Drone
- Adopt USB side-mount, easy to plug in
- All of solder pads are at the edge of FC, which is a convenience to solder
- Double-sided motor solder pad. Pins pad and wires pad are both built-in for motors connection
- Integrated with a Betaflight MATEKF411RX processor FC, Betaflight OSD and 2-4S 12A ESC, support 4S battery for fast-flying experience
Specification
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 (100MHZ)
Six-Axis: MPU6000 (SPI connection)
Size: 32.5*32.5mm (26.5mm mounting holes)
Firmware version: Betaflight MATEKF411 (MK41)
OSD: Build-in BetaFlight OSD (OSD chip: AT7456E)
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver.
Support programmable LED like WS2812 etc
Built-in current sensor
Weight: 6.2g(Without Pins), 6.5g(Pins Pre-solder)
SPECIFICATIONS OF ESC
Support BLheli/BLHELI_S suite Pass-through ready
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4S Lipo
Continue current: 12A
Peak current: 15A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G-C
Motor Connectors: 1.25mm header pins connector
Factory firmware: G-H-30-16.7
In The Box
1 * Toothpick F4 2S - 4S AIO 12A brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
Videos
FAQ
Downloads
Reviews
Write your review
You must be logged in to post a review.