True
  1. Products
  2. Matek CRSF to PWM Converter (ExpressLRS Compatible)
Product Image
  • LRS Systems ,
  • RC transmitter

    • Matek CRSF to PWM Converter (ExpressLRS Compatible)

    6.99 € 6.99 €
    Add to Cart
    Matek CRSF to PWM Converter (ExpressLRS Compatible)

    Matek CRSF to PWM Converter (ExpressLRS Compatible)

    Create a new review
    3

    6.99 € 6.99 € 6.99 EUR

    5.78 €

    (0% Off)
    Ex. Tax: 5.78 € 5.776859504132231 EUR
    Days
    :
    Hours
    :
    Mins
    :
    Secs
    • RC Systems
    • RC Systems

    This combination does not exist.

    Add to Cart
    SKU:
    N/A
    Brand:  Mateksys CRSF-PWM6
    Mateksys
    CRSF-PWM6
    5 1 1
    Share :
    •  True Stock of Products
    •    Fast & Free Shipping*
    •   Secure Payment


    Specifications:


    • Compatible with CRSF protocol receiver only

    • Support any CRSF protocol receivers(including 433MHz, 868MHz, 915MHz, 2.4GHz)

    • 6x PWM outputs

    • PWM frequency configurable (50Hz default, 100,160,330, 400Hz)

    • 2x UARTs (for Receiver and GPS)

    • Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats

    • 36V Max. battery voltage sense (1K:10K voltage divider built-in)

    • Compatible with external Current sensor (0~3.3V)

    • Vbat and Current sensor scale configurable

    • Failsafe value auto set

    • Firmware upgradeable

    • Rated voltage: 4~9V @5V pad, 0~36V @Vbat, 0~3.3V @Curr

    • No 5V regulator built-in

    • 25mm x 16mm, 1.3g




    Specifications for Matek CRSF to PWM Converter (ExpressLRS Compatible)

    RC Systems Accessories , Receivers

    Pinouts and Pads

    Tx1/Rx1(UART1) for CRSF protocol Receiver

    Tx2/Rx2(UART2) for GPS/firmware update/setting parameters

    1~10: CH1~CH10 PWM outputs

    Curr: current sensor signal (0~3.3V)

    Vbat: Battery voltage sensing (0~36V)

    G: ground

    4v5 pad voltage = 5V pad voltage -0.3V,  make sure the voltage on 5V pad is not higher than receiver and GPS rated voltage.


    Failsafe

    Failsafe value is set automatically after CRSF-PWM board is powered on and receive CRSF signal. LED blinks 8 times quickly.

    Failsafe value = The PWM value of each channel(except CH3) when CRSF signal is received by CRSF-PWM board for the first time

    CH3 is specially arranged for the throttle,  Failsafe value = 988 by default.

    Usually put the Throttle  joystick to the lowest point,  put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on receiver.


    LED status

    slow blinks: CRSF-PWM board doesn’t receive CRSF signal, e.g., receiver is not bound with transmitter, receiver is not connected to UART1 of CRSF-PWM board.

    8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.

    solid ON:  CRSF-PWM board and receiver are working normally

    2x slow blinks between 8x fast blink and solid on: CLI mode is active


    GPS telemetry

    Compatible with GPS NMEA protocol

    GPS “TX” to CRSF-PWM board “RX” Single wire half duplex UART connection,   CRSF-PWM board “TX” to GPS “RX” is not essential.

    Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats

    u-blox series GPS can output “0+1 – UBX+NMEA” protocol by default

    Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in Transmitter TELEMETRY tab once CRSF-PWM board has connection with GPS.

    Troubleshooting for no GPS telemetry,  double check the wiring between GPS and CRSF-PWM board,  some u-blox GPS may don’t output NMEA protcol, you need to be reverted GPS to default configuration in u-center.

    with OpenTX Telemetry Logging, You can plot your flight path or search the lost plane.


    TIM & PWM Frequency

    PWM frequency on all 10x Channels can be configured according to TIM

    PWM run at 50Hz by default

    TIM2:  CH1, CH2, CH4

    TIM16: CH3

    TIM3:  CH5, CH6, CH7, CH8

    TIM1:  CH9, CH10


    CLI mode

    If CRSF-PWM board doesn’t detect GPS connected to UART2 within 10 seconds after powering on,  CLI mode will active.

    After CLI mode is active, CRSF-PWM board can be connected to configurator via USB-TTL module/FC passthrough.

    in CLI mode, CRSF-PWM board firmware can be updated

    CLI mode has no effect to receiver CRSF signal and PWM outputs

    1x Matek CRSF to PWM Converter (ELRS Compatible)

    1x Pin set

    MANUAL & Firmware

    <p><br></p><h4><b>Specifications:</b></h4><p><br></p><ul><li><p>Compatible with CRSF protocol receiver only</p></li></ul><ul><li><p>Support any CRSF protocol receivers(including 433MHz, 868MHz, 915MHz, 2.4GHz)</p></li></ul><ul><li><p>6x PWM outputs</p></li></ul><ul><li><p>PWM frequency configurable (50Hz default, 100,160,330, 400Hz)</p></li></ul><ul><li><p>2x UARTs (for Receiver and GPS)</p></li></ul><ul><li><p>Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats</p></li></ul><ul><li><p>36V Max. battery voltage sense (1K:10K voltage divider built-in)</p></li></ul><ul><li><p>Compatible with external Current sensor (0~3.3V)</p></li></ul><ul><li><p>Vbat and Current sensor scale configurable</p></li></ul><ul><li><p>Failsafe value auto set</p></li></ul><ul><li><p>Firmware upgradeable</p></li></ul><ul><li><p>Rated voltage: 4~9V @5V pad, 0~36V @Vbat, 0~3.3V @Curr</p></li></ul><ul><li><p>No 5V regulator built-in</p></li></ul><ul><li><p>25mm x 16mm, 1.3g</p></li></ul><p><br></p><p><img src="/web/image/378201/CRSF-PWM-6_conversor_elrs_matek_banner.jpeg?access_token=f531bc9b-d6d8-4b99-9edf-8506ea67c0e2" class="pull-left" style=""><br></p><p><img src="/web/image/378200/CRSF-PWM-6_conversor_elrs_matek_banner1.jpeg?access_token=93f9b0e2-9af8-4336-9d22-bfe624e737fd" class="pull-left" style=""><br></p>

    Suggested Products

    Matek ExpressLRS R24-D 2.4GHz SPI Receiver
    Matek ExpressLRS R24-D 2.4GHz SPI Receiver
    21.50 € 21.50 €
    This is a preview of the recently viewed products by the user.
    Once the user has seen at least one product this snippet will be visible.

    Recently viewed Products

    To install this Web App in your iPhone/iPad press and then Add to Home Screen.