Matek F405 WSE
https://rc-innovations.es/matek-f405-wse-inavflight-matek-wing-flight-controllerFlight Controller F405WSE WING of Matek for Aircraft, with a micro STM32F405 MCU, and frequency of up to 168Mhz. The firmware of the flight controller is iNavFlight.
FC Specifications
MCU: 168MHz STM32F405
IMU: MPU6000 accelerometer/gyro (SPI)
Baro: DPS310
OSD: INAV OSD w/ AT7456E chip
Blackbox: MicroSD card slot (SD/SDHC)
VCP & 6x UARTs
10 PWM outputs
2x I2C
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
Built in inverter for SBUS input (UART2-RX)
PPM/UART Shared: UART2-RX
SoftSerial on TX2 pad
Battery Voltage Sensor: 1:10 (Scale 1100)
WS2812 Led Strip : Yes
Beeper : Yes
RSSI: Yes
FC Specifications
MCU: 168MHz STM32F405RGT6 1MB Flash
IMU: MPU6000 (SPI1)
Baro: DPS310 (I2C1)
OSD: AT7456E (SPI2)
Blackbox: MicroSD socket (SPI3)
VCP & 6x UARTs,
1x Softserial_Tx option (TX2 pad, INAV)
10x PWM outputs(S1~S9, LED)
2x I2C
3x ADC (voltage, current, RSSI)
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
Built in inverter on UART2-RX for SBUS input
PPM/UART Shared: UART2-RX
1x SH1.0_6pin connector (4V5/G/TX4/RX4/DA2/CL2) for GPS/compass
1x SH1.0_6pin connector for external USB and buzzer
DJI FPV OSD: any spare UART
FrskyOSD: any spare UART
Power
6~30V DC IN (2~6S LiPo)
132A high-precision Current Sense (Scale 250)
PDB/Current sense resistor: 60A continuous, 132A burst.
BEC 5V 2A for FC & Peripherals
BEC Vx 5A for servos, 5V/ 6V option
BEC 8V 1.5A for VTX and camera
LDO 3.3V 200mA
Battery Voltage Sensor: 1k:10k
FC Firmware
INAV Target: MATEKF405SE
ArduPilot hwdef: MATEKF405WING
Physical
Dimensions: 44 x 29 x 10 mm
Mounting: 25 x 25mm, Φ2mm
Weight: 20g w/ bottom plate and USB/buzzer adapter
1x FC F405-WSE
1x USB(Type-C)/Buzzer (Active) Adapter
1x Bottom plate, 44 x 29mm
2x JST-SH-6P to JST-SH-6P cables, 20cm
5x Brass standoffs, M2*4mm
10x screws, M2*3.5mm
Dupont 2.54 pins (Board is shipped unsoldered)
F722 VS F405 & F411
| F411-WSE | F411-WING | F722-WING | F405-WING | |
| TARGET | MATEKF411SE | MATEKF411 | MATEKF722SE | MATEKF405SE |
| MCU | 100MHz STM32F411 | 100MHz STM32F411 | 216MHz STM32F722 | 168MHz STM32F405 |
| IMU | MP6000 | MP6000 | MP6000 | MP6000 |
| BARO | BMP280 | BMP280 | BMP280 | BMP280 |
| OSD | AT7456E | AT7456E | AT7456E | AT7456E |
| BlackBox | / | / | MicroSD | MicroSD |
| Firmware | INAV | INAV BetaFlight | INAV BetaFlight | INAV ArduPilot |
| Dual Camera In | Yes | / | Yes | / |
| 5V/9V Switcher | / | / | Yes | / |
| Current Sense | 78A | 78A | High precision 132A | 104A |
| Max.Voltage | 30V(6S) | 30V(6S) | 36V(8S) | 30V(6S) |
| Motors | 2 | 2 | 2 | 2 |
| Servos | 4 | 5 | 6 | 7 |
| UART | 2 | 2 | 5 | 6 |
| Softserial | 2 | 1 | 1 | 1 |
| Uart Inversion | RX2 | RX1 | All | RX2 |
| 5V | 2A | 2A | 2A | 2A |
| 9V | / | / | 2A | 2A |
| Vx | 3.5A cont. 5A Max.(5s) | 3A cont. | 5A cont. 6A Max.(5s) | 5A cont. 6A Max.(5s) |
| 3.3V | 200mA | 200mA | 200mA | 500mA |
Write your review
You must be logged in to post a review.
Description
Flight Controller F405WSE WING of Matek for Aircraft, with a micro STM32F405 MCU, and frequency of up to 168Mhz. The firmware of the flight controller is iNavFlight.
FC Specifications
MCU: 168MHz STM32F405
IMU: MPU6000 accelerometer/gyro (SPI)
Baro: DPS310
OSD: INAV OSD w/ AT7456E chip
Blackbox: MicroSD card slot (SD/SDHC)
VCP & 6x UARTs
10 PWM outputs
2x I2C
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
Built in inverter for SBUS input (UART2-RX)
PPM/UART Shared: UART2-RX
SoftSerial on TX2 pad
Battery Voltage Sensor: 1:10 (Scale 1100)
WS2812 Led Strip : Yes
Beeper : Yes
RSSI: Yes
Specification
FC Specifications
MCU: 168MHz STM32F405RGT6 1MB Flash
IMU: MPU6000 (SPI1)
Baro: DPS310 (I2C1)
OSD: AT7456E (SPI2)
Blackbox: MicroSD socket (SPI3)
VCP & 6x UARTs,
1x Softserial_Tx option (TX2 pad, INAV)
10x PWM outputs(S1~S9, LED)
2x I2C
3x ADC (voltage, current, RSSI)
3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
Built in inverter on UART2-RX for SBUS input
PPM/UART Shared: UART2-RX
1x SH1.0_6pin connector (4V5/G/TX4/RX4/DA2/CL2) for GPS/compass
1x SH1.0_6pin connector for external USB and buzzer
DJI FPV OSD: any spare UART
FrskyOSD: any spare UART
Power
6~30V DC IN (2~6S LiPo)
132A high-precision Current Sense (Scale 250)
PDB/Current sense resistor: 60A continuous, 132A burst.
BEC 5V 2A for FC & Peripherals
BEC Vx 5A for servos, 5V/ 6V option
BEC 8V 1.5A for VTX and camera
LDO 3.3V 200mA
Battery Voltage Sensor: 1k:10k
FC Firmware
INAV Target: MATEKF405SE
ArduPilot hwdef: MATEKF405WING
Physical
Dimensions: 44 x 29 x 10 mm
Mounting: 25 x 25mm, Φ2mm
Weight: 20g w/ bottom plate and USB/buzzer adapter
In The Box
1x FC F405-WSE
1x USB(Type-C)/Buzzer (Active) Adapter
1x Bottom plate, 44 x 29mm
2x JST-SH-6P to JST-SH-6P cables, 20cm
5x Brass standoffs, M2*4mm
10x screws, M2*3.5mm
Dupont 2.54 pins (Board is shipped unsoldered)
Videos
FAQ
F722 VS F405 & F411
| F411-WSE | F411-WING | F722-WING | F405-WING | |
| TARGET | MATEKF411SE | MATEKF411 | MATEKF722SE | MATEKF405SE |
| MCU | 100MHz STM32F411 | 100MHz STM32F411 | 216MHz STM32F722 | 168MHz STM32F405 |
| IMU | MP6000 | MP6000 | MP6000 | MP6000 |
| BARO | BMP280 | BMP280 | BMP280 | BMP280 |
| OSD | AT7456E | AT7456E | AT7456E | AT7456E |
| BlackBox | / | / | MicroSD | MicroSD |
| Firmware | INAV | INAV BetaFlight | INAV BetaFlight | INAV ArduPilot |
| Dual Camera In | Yes | / | Yes | / |
| 5V/9V Switcher | / | / | Yes | / |
| Current Sense | 78A | 78A | High precision 132A | 104A |
| Max.Voltage | 30V(6S) | 30V(6S) | 36V(8S) | 30V(6S) |
| Motors | 2 | 2 | 2 | 2 |
| Servos | 4 | 5 | 6 | 7 |
| UART | 2 | 2 | 5 | 6 |
| Softserial | 2 | 1 | 1 | 1 |
| Uart Inversion | RX2 | RX1 | All | RX2 |
| 5V | 2A | 2A | 2A | 2A |
| 9V | / | / | 2A | 2A |
| Vx | 3.5A cont. 5A Max.(5s) | 3A cont. | 5A cont. 6A Max.(5s) | 5A cont. 6A Max.(5s) |
| 3.3V | 200mA | 200mA | 200mA | 500mA |
Reviews
Write your review
You must be logged in to post a review.