
Matek F722HD flight controller for FPV racing drones, STM32F722 MCU, Frequency up to 216Mhz, Flight controller firmware is working the F722 to the limit.
Now is fully compatible with DJI FPV System and Caddx Vista
Features:
- Latest generation processor STM32F722RET6
- IMU: MPU6000 (SPI)
- BMP 280 Barometer
- OSD: Support external DJI OSD/FrskyOSD, No Analog MAX7456 OSD built-in
- Support INAV Firmware
- Dshot Outputs
- 10 PWM outputs
- Blackbox: 32M-byte Flash memory (SPI)
- 6 Uarts ports
- Compatible with FrSky telemetry
* More info: MATEK WEBSITE
- MCU: 216MHz STM32F722RET6
- IMU: MPU6000 (SPI)
- Baro: BMP280 (I2C)
- OSD: Support external DJI OSD/FrskyOSD, No Analog MAX7456 OSD built-in
- Blackbox: 32M-byte Flash memory (SPI)
- VCP, UART1, UART2, UART3, UART4, UART5, UART6
- PPM/UART Shared: UART2-RX
- Battery Voltage Sensor: 1:10
- Current Sensor: No
- BEC 5V: 2A cont, (3 Max)
- BEC: 8V 2A cont. (Max.3A)
- LDO 3.3V: Max.200mA
- I2C1 SDA & SCL: Yes
- Camera control: Yes
- WS2812 Led Strip : Yes
- Beeper : Yes
- RSSI: Yes
- 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
- 10x PWM / DShot outputs without conflict
- 6x UARTs
- 1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
- 1x I2C1
- 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
- 1x Side-press button for BOOT(DFU) mode
- 1x 16pin bottom mounted FFC Slot for FCHUB-6S or FCHUB-VTX connection
- 36x36mm PCB with 30.5mm mounting holes
1x FC F722-HD
6x Silicon grommets M4 to M3
1x SH1.0_8pin cable 5cm
2x SH1.0_8pin connectors
1x SH1.0_6pin to GH1.25_8pin cable 8cm
Write your review
You must be logged in to post a review.
Description
Matek F722HD flight controller for FPV racing drones, STM32F722 MCU, Frequency up to 216Mhz, Flight controller firmware is working the F722 to the limit.
Now is fully compatible with DJI FPV System and Caddx Vista
Features:
- Latest generation processor STM32F722RET6
- IMU: MPU6000 (SPI)
- BMP 280 Barometer
- OSD: Support external DJI OSD/FrskyOSD, No Analog MAX7456 OSD built-in
- Support INAV Firmware
- Dshot Outputs
- 10 PWM outputs
- Blackbox: 32M-byte Flash memory (SPI)
- 6 Uarts ports
- Compatible with FrSky telemetry
* More info: MATEK WEBSITE
Specification
- MCU: 216MHz STM32F722RET6
- IMU: MPU6000 (SPI)
- Baro: BMP280 (I2C)
- OSD: Support external DJI OSD/FrskyOSD, No Analog MAX7456 OSD built-in
- Blackbox: 32M-byte Flash memory (SPI)
- VCP, UART1, UART2, UART3, UART4, UART5, UART6
- PPM/UART Shared: UART2-RX
- Battery Voltage Sensor: 1:10
- Current Sensor: No
- BEC 5V: 2A cont, (3 Max)
- BEC: 8V 2A cont. (Max.3A)
- LDO 3.3V: Max.200mA
- I2C1 SDA & SCL: Yes
- Camera control: Yes
- WS2812 Led Strip : Yes
- Beeper : Yes
- RSSI: Yes
- 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
- 10x PWM / DShot outputs without conflict
- 6x UARTs
- 1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
- 1x I2C1
- 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
- 1x Side-press button for BOOT(DFU) mode
- 1x 16pin bottom mounted FFC Slot for FCHUB-6S or FCHUB-VTX connection
- 36x36mm PCB with 30.5mm mounting holes
In The Box
1x FC F722-HD
6x Silicon grommets M4 to M3
1x SH1.0_8pin cable 5cm
2x SH1.0_8pin connectors
1x SH1.0_6pin to GH1.25_8pin cable 8cm
Videos
FAQ
Downloads
Reviews
Write your review
You must be logged in to post a review.