
Features
- u-blox M9N engine GPS, Beidou, GLONASS, Galileo
- Build-in embedded GNSS patch antenna, low power consumption
- The 25 x 25 mm patch antenna
- Magnetic sensor QMC5883L integrated
- Weight: 14.5 gram
- Can be easy mounted in your case by double sided tape
- Supported by INAV/Betaflight/Ardupilot, etc.
Tips
- GPS, GLONASS, SBAS, QZSS are enabled by default
- Blue PPS LED blinking(1Hz) means 3D fixed
- update rate 1Hz & baudrate 9600 default
- Baud 9600~115200 supported by INAV
- update rate 5Hz with INAV UBLOX Protocol
- update rate 10Hz with INAV UBLOX7 Protocol
- Compass Alignment(Arrow forward): INAV/BF: CW 270° Flip; Ardupilot/Mission Planner: Rotation None
- BF doesn’t support GPS position hold and RTH, GPS Rescue mode is supported by BF3.5 or last.
- No need compass for Fixed wings with INAV firmware
- The scratches on ceramic antenna are the result of tuning the antenna by ublox. Placing small nicks in the centre of the long edges, or corners, brings them into spec
GNSS u-blox NEO-M9N (GPS, GLONASS, Galileo and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 25*25*4mm
Input voltage range: 4~6V (5V pad/pin)
Power consumption: 50mA
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS NEO-M9N
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector
3.3V Power LED, Red
GNSS PPS LED, Green, blinking(1Hz) when GNSS has 3D fixed
32mm*32mm*10mm
14.5g
1x Matek M9N
1x JST-GH-6P to JST-GH-6P 20cm silicon wire
Write your review
You must be logged in to post a review.
Description
Features
- u-blox M9N engine GPS, Beidou, GLONASS, Galileo
- Build-in embedded GNSS patch antenna, low power consumption
- The 25 x 25 mm patch antenna
- Magnetic sensor QMC5883L integrated
- Weight: 14.5 gram
- Can be easy mounted in your case by double sided tape
- Supported by INAV/Betaflight/Ardupilot, etc.
Tips
- GPS, GLONASS, SBAS, QZSS are enabled by default
- Blue PPS LED blinking(1Hz) means 3D fixed
- update rate 1Hz & baudrate 9600 default
- Baud 9600~115200 supported by INAV
- update rate 5Hz with INAV UBLOX Protocol
- update rate 10Hz with INAV UBLOX7 Protocol
- Compass Alignment(Arrow forward): INAV/BF: CW 270° Flip; Ardupilot/Mission Planner: Rotation None
- BF doesn’t support GPS position hold and RTH, GPS Rescue mode is supported by BF3.5 or last.
- No need compass for Fixed wings with INAV firmware
- The scratches on ceramic antenna are the result of tuning the antenna by ublox. Placing small nicks in the centre of the long edges, or corners, brings them into spec
Specification
GNSS u-blox NEO-M9N (GPS, GLONASS, Galileo and BeiDou)
Magnetic Compass QMC5883L
Patch antenna 25*25*4mm
Input voltage range: 4~6V (5V pad/pin)
Power consumption: 50mA
Operating Temperatures: -20~80 °C
UART(TX, RX) interface for GNSS NEO-M9N
I2C(DA, CL) interface for Compass QMC5883L
JST-GH-6P connector
3.3V Power LED, Red
GNSS PPS LED, Green, blinking(1Hz) when GNSS has 3D fixed
32mm*32mm*10mm
14.5g
In The Box
1x Matek M9N
1x JST-GH-6P to JST-GH-6P 20cm silicon wire
Videos
FAQ
Downloads
Reviews
Write your review
You must be logged in to post a review.