True
  1. Products
  2. Autopilots & stabilizers
  3. Matek GPS GNSS Module M9N & 5883L Compass
Product Image
  • Autopilots & stabilizers ,
  • Flight controllers

    • Matek GPS GNSS Module M9N & 5883L Compass

    50.90 € 50.90 €
    Add to Cart
    Matek GPS GNSS Module M9N & 5883L Compass
    Módulo GPS GNSS Matek M9N & Brújula 5883L
    Módulo GPS GNSS Matek M9N & Brújula 5883L
    1. Matek GPS GNSS Module M9N & 5883L Compass
    2. Módulo GPS GNSS Matek M9N & Brújula 5883L
    3. Módulo GPS GNSS Matek M9N & Brújula 5883L

    Matek GPS GNSS Module M9N & 5883L Compass

    Create a new review
    3

    50.90 € 50.90 € 50.9 EUR

    42.07 €

    (0% Off)
    Ex. Tax: 42.07 € 42.06611570247934 EUR
    Days
    :
    Hours
    :
    Mins
    :
    Secs
    • Accessories

    This combination does not exist.

    Add to Cart
    SKU:
    N/A
    Brand:  Mateksys M9N-5883
    Mateksys
    M9N-5883
    5 1 1
    Share :
    •  True Stock of Products
    •    Fast & Free Shipping*
    •   Secure Payment

    M9N-5883 uses multi-constellation GNSS powered by NEO-M9N , NEO-M9N is a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently.



    Tips and Notes


    Compass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged !

    INAV/BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward.

    INAV/BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward.

    Ardupilot/Mission Planner: Rotation None.

    Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material

    INAV 5.0.0, Betaflight 4.3.0,  ArduPilot 4.3 or newer is required.

    NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in.  once GNSS is powered off and the supercapacitor run out. the settings will back to default.

    UBX protocol is bidirectional.  Flight controller firmware can change settings on GPS via UBX protocol. You don’t need to set GNSS module parameters in u-center.

    Start with GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed.

    The M9N-5883 provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset.

    The scratches on ceramic antenna are the result of tuning the antenna.

    Troubleshoot GPS related issues: https://www.mateksys.com/?p=5712#tab-id-6

    u-center Windows

    Specifications for Matek GPS GNSS Module M9N & 5883L Compass

    Accessories GPS - GNSS - RTK

    GNSS NEO-M9N (GPS, GLONASS, Galileo and BeiDou)

    Magnetic Compass QMC5883L

    Patch antenna 25*25*4mm

    Input voltage range: 4~5.5V (5V pad/pin)

    Power consumption: 50mA

    UART baudrate: 38400 default

    Operating Temperatures: -20~80 °C

    UART(TX, RX) interface for GNSS NEO-M9N

    I2C(DA, CL) interface for Compass QMC5883L

    JST-GH-6P connector

    3.3V Power LED, Red

    GNSS PPS LED, Green,  blinking(1Hz) when GNSS has 3D fixed

    32mm*32mm*10mm

    14.5g

    1x M9N-5883

    1x JST-GH-6P to JST-GH-6P 20cm silicon wire

    SKUM10-L4-3100M10-5993M9N-5883M8Q-5883
    ubloxMAX-M10SMAX-M10SNEO-M9NSAM-M8Q
    GNSSGPS
    BeiDou
    GLONASS
    Galileo    		GPS
    BeiDou
    GLONASS
    Galileo    		GPS
    BeiDou
    GLONASS
    Galileo    		GPS
    GLONASS
    Galileo
    Position accuracy1.5m CEP1.5m CEP2.0m CEP2.5m CEP
    Tracking and nav.-168 dBm-168 dBm-167 dBm–165 dBm
    Reacquisition-160 dBm-160 dBm-160 dBm–158 dBm
    Cold start-148 dBm-148 dBm-148 dBm–146 dBm
    Hot start-159 dBm-159 dBm-159 dBm–155 dBm
    Nav. update rate5Hz, 10Hz5Hz, 10Hz5Hz5Hz, 10Hz
    CompassRM3100QMC5883LQMC5883LQMC5883L
    BaroSPL06-001///
    InterfaceCAN
    4Wires
    JST-GH connector    		UART+I2C
    6Wires
    JST-GH connector    		UART+I2C
    6Wires
    JST-GH connector    		UART+I2C
    6Wires
    JST-SH connector
    CAN Nodesupport Digital AirSpeed///
    SIZE36*36*1223*23*1032*32*1020*20*10
    Weight16g9g15g7g

    MANUAL, Firmware

    <p>M9N-5883 uses multi-constellation GNSS powered by NEO-M9N , NEO-M9N is a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently.<br></p><p><br></p><p><br></p><h4><b>Tips and Notes</b></h4><h4><b><br></b></h4><p>Compass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged !</p><p>INAV/BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward.</p><p>INAV/BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward.</p><p>Ardupilot/Mission Planner: Rotation None.</p><p>Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material</p><p>INAV 5.0.0, Betaflight 4.3.0, &nbsp;ArduPilot 4.3 or newer is required.</p><p>NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in. &nbsp;once GNSS is powered off and the supercapacitor run out. the settings will back to default.</p><p>UBX protocol is bidirectional. &nbsp;Flight controller firmware can change settings on GPS via UBX protocol. You don’t need to set GNSS module parameters in u-center.</p><p>Start with GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed.</p><p>The M9N-5883 provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset.</p><p>The scratches on ceramic antenna are the result of tuning the antenna.</p><p>Troubleshoot GPS related issues: https://www.mateksys.com/?p=5712#tab-id-6</p><p>u-center Windows</p>

    This is a preview of the recently viewed products by the user.
    Once the user has seen at least one product this snippet will be visible.

    Recently viewed Products

    To install this Web App in your iPhone/iPad press and then Add to Home Screen.