<p>The HUBOSD8-SE has been engineered to provide the highest possible performance and reliability in a 46*36mm &amp; 4 layers PCB.&nbsp;<span style="line-height: 1.42857;">It is a multifunctional HUB with PDB, BEC 5V/1.5A &amp;10V/1.5A, Current sensor 184A, STOSD8-SE. It is specially made for the mini FPV Quad.&nbsp;</span><span style="line-height: 1.42857;">The BEC 12V is linear regulator, no LC Filter needed. Built-in STOSD8-SE can support Plug &amp; Play, no complicated settings needed.</span></p><p><span style="line-height: 1.42857;"><br></span></p><h4><span style="font-weight: bold;">General</span></h4><p>Input voltage range (3S-6S operation): 9 - 27VDC</p><p>PDB: 4x30A (Max.4x46A)</p><p>Regulated 5V and 10V outputs</p><p>Current Sensor 184A</p><p>Built-in STOSD8-SE</p><h5><span style="font-weight: bold;">Physical:</span></h5><p>- 2oz copper, 4-layers &amp;1.6mm PCB.</p><p>- 1x Battery input, 4x ESC outputs. 2x BEC 5V outputs, 2x BEC 12V outputs.</p><p>- Camera signal &amp; Gnd pads, Video Transmitter Signal &amp; Gnd pads</p><p>- 1x Serial port (RX, TX, G)</p><p>- Dimensions: 46x36x4mm, Weight: 9g</p><p>- Mounting holes 30.5mm square spacing，Φ3mm</p><p><br></p><h4><span style="font-weight: bold;">PDB (ESC outputs)</span></h4><p>Continuous current: 30A per output</p><p>Peak current (10 seconds/minute): 46A per output</p><p><br></p><h4><span style="font-weight: bold;">BEC 5V outputs</span></h4><p>Designed for RC Receivers, Flight controllers, OSD, and Servos.</p><p>DC/DC synchronous buck regulator.</p><p>Voltage: 5.0 +/- 0.1VDC</p><p>Continuous current: 2 Amps (Max.2.5A 10s/minute)</p><p>Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)</p><p>Short-circuit tolerant (5 seconds/minute)</p><p><br></p><h4><span style="font-weight: bold;">BEC 12V outputs</span></h4><p>Linear regulator, very low noise. LC Filter is needless.</p><p>Designed for Video TX or FPV camera.</p><p>Voltage: 12.0 +/- 0.3VDC (4~5S operation)</p><p>Continuous current: 1.5A@16V IN</p><p>Short-circuit tolerant (2 seconds/minute)</p><p>If the battery is 3S LiPo, Output voltage=3S LiPo voltage - 1V</p><p><br></p><h4><span style="font-weight: bold;">Current Sensor</span></h4><p>184A</p><p></p><p>If current &gt;184A. STOSD display 184A</p><p><br></p><h4><span style="font-weight: bold;">More info OSD:</span></h4><h4><span style="font-weight: bold;"><br></span></h4><h4><span style="font-weight: bold;"><br></span><a href="http://www.stosd.com/" target="_blank">http://www.stosd.com/</a><span style="font-weight: bold;"><br></span><br></h4><p><br></p>