True
  1. Products
  2. Autopilots & stabilizers
  3. Matek AP_PERIPH CAN Node
Product Image
  • Autopilots & stabilizers ,
  • Flight controllers

    • Matek AP_PERIPH CAN Node

    22.90 € 22.90 €
    Add to Cart
    Matek AP_PERIPH CAN Node

    Matek AP_PERIPH CAN Node

    Create a new review
    3

    22.90 € 22.90 € 22.900000000000002 EUR

    18.93 €

    (0% Off)
    Ex. Tax: 18.93 € 18.925619834710744 EUR
    Days
    :
    Hours
    :
    Mins
    :
    Secs
    • Accessories

    This combination does not exist.

    Add to Cart
    SKU:
    N/A
    Brand:  Mateksys CAN-G474
    Mateksys
    CAN-G474
    5 1 1
    Share :
    •  True Stock of Products
    •    Fast & Free Shipping*
    •   Secure Payment

    CAN-G474 is an Adapter Node based on ArudPilot AP_Periph firmware.

    with 5Mbit/s CAN transceiver and STM32G474 MCU, CAN-G474 is capable of CANFD.

    With this board, you can easily utilize the ArduPilot driver library to convert ArduPilot supported GNSS, Compass, Barometer, Airspeed sensor, Rangefinder, Proximity sensor, Electronic Fuel Injectors and GPIO based (PWM, LED notify) peripherals to DroneCAN bus peripherals.





    Specifications for Matek AP_PERIPH CAN Node

    Accessories Sensors - Spare Parts
    • MCU: STM32G474CE, 512KB Flash
    • CAN transceiver data rates up to 5Mbit/s
    • 2x CAN bus
    • 4x UARTs
      • for peripheral GNSS, Rangefinder, Proximity, EFI, RC input(receiver)
      • support GNSS, Compass, Barometer sensors over MSP protocol. MSP is enable on TX3 by default.
    • 2x I2C bus
      • for peripheral I2C Airspeed sensor, Barometer, Compass
    • 1x SPI
      • for peripheral RM3100
      • SPI pads for RM3100 are on bottom side, with “CS, MOSI, MISO, SCK” silkprint
    • 11x PWM outputs
      • for Servos and ESC, all PWMs support DMA/DShot
      • PWM1-10 on DuPont 2.54mm holes
      • PWM11 pad is on bottom side, with “11” silkprint
    • ST debug, SWC & SWD(on bottom side)
    • UART1(TX1,RX1) support firmware update in DFU mode
    • LED
      • Blue, Fast blinking,  Booting
      • Blue, Slow blinking, communicating with flight controller
      • Red, 3.3V indicator
    • Input voltage range: 4.5~5.5V  @5V pad/pin
    • Power consumption: 62mA
    • Operating Temperatures: -30~85 °C

    Physical

    • 5x JST-GH-4P(SM04B-GHS-TB) for CAN1, CAN2, I2C1, UART1 and UART4
    • 1x JST-GH-6P(SM06B-GHS-TB) for UART3+I2C2
    • 18x DuPont 2.54mm holes
    • Board Size: 36mm*36mm*6mm.  5.2g,
    • Mounting: 30.5mm 4x Dia.3mm
    • 3D file : CAN-G474_STEP.zip

    1x CAN-G474 board

    2x JST-GH-4P to JST-GH-4P 20cm silicon wire

    1x JST-GH-6P to JST-GH-6P 20cm silicon wire

    • ArduPilot AP_Periph  MatekG474-Periph for peripheral sensors
    • ArduPilot AP_Periph  MatekG474-DShot for DroneCAN-PWM output
    • Update via DroneCAN GUI Tool or Mission Planner–DroneCAN Tab, load “AP_Periph.bin“
    • Update via STM32CubeProgrammer in DFU mode,  connect USB-TTL module to UART1, Plug USB while holding the DFU button in,  load “AP_Periph_with_bl.hex“.
    <p>CAN-G474 is an Adapter Node based on ArudPilot AP_Periph firmware.</p><p>with 5Mbit/s CAN transceiver and STM32G474 MCU, CAN-G474 is capable of CANFD.</p><p>With this board, you can easily utilize the ArduPilot driver library to convert ArduPilot supported GNSS, Compass, Barometer, Airspeed sensor, Rangefinder, Proximity sensor, Electronic Fuel Injectors and GPIO based (PWM, LED notify) peripherals to DroneCAN bus peripherals.</p><p><br></p><p><br></p><p><br></p><p><br></p>

    This is a preview of the recently viewed products by the user.
    Once the user has seen at least one product this snippet will be visible.

    Recently viewed Products

    To install this Web App in your iPhone/iPad press and then Add to Home Screen.