Introduction
1.1 Compatibility:
FASST 2.4G Air Systems (7CH Mode/Multi Mode): 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc.
1.2 Specifications:
Number of Channels: up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10)
Number of Channels: up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10)
With RSSI Output
Operating Voltage Range: 3.5V~10V
Operating Voltage Range: 3.5V~10V
Operating Temperature Range: -10℃~60℃
Dimension: 53mm*30mm*11mm
Dimension: 53mm*30mm*11mm
Weight: 13.5g
2.Setup
| Warning: Servos are not to be plugged into Channel CPPM and Channel RSSI, otherwise servos will get hot or may burn out. Note: Increased duty means good signal reception, and vice verse. |
2.1 Bind procedure:
Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.
2.2 Setting failsafe:
TFRSP supports failsafe function for all channels. Follow the steps below to set failsafe:
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.
| Warning: Some transmitter manufacturers use a failsafe method that can interfere with that used by FrSky. Be sure to disable any transmitter failsafe settings before setting FrSky failsafe positions. Unusual jitter may result otherwise. |
| RED LED | GREEN LED | Mode |
| Off | On | Normal mode |
| On | On | Waiting to be bound |
| Flashing | On | Signal lost |
| On | Flashing twice | Set failsafe |
CPPM is usable for reducing wirings to some flybar-less controllers, autopilot systems and homebrew UAV systems. Furthermore, it can be used as a wireless trainer system.
Please find the how-to guide with the file named “Set up FrSky as a wireless trainer system” via the following link: www.frsky-rc.com/download.asp?id=23
Introduction
1.1 Compatibility:
FASST 2.4G Air Systems (7CH Mode/Multi Mode): 6EX, 7C, TM-7, TM-8, T8FG, T10C, TM-10, T10CG, T12Z, T12FG, TM-14, T14MZ, etc.
1.2 Specifications:
Number of Channels: up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10)
Number of Channels: up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10)
With RSSI Output
Operating Voltage Range: 3.5V~10V
Operating Voltage Range: 3.5V~10V
Operating Temperature Range: -10℃~60℃
Dimension: 53mm*30mm*11mm
Dimension: 53mm*30mm*11mm
Weight: 13.5g
2.Setup
| Warning: Servos are not to be plugged into Channel CPPM and Channel RSSI, otherwise servos will get hot or may burn out. Note: Increased duty means good signal reception, and vice verse. |
2.1 Bind procedure:
Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.
2.2 Setting failsafe:
TFRSP supports failsafe function for all channels. Follow the steps below to set failsafe:
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.
| Warning: Some transmitter manufacturers use a failsafe method that can interfere with that used by FrSky. Be sure to disable any transmitter failsafe settings before setting FrSky failsafe positions. Unusual jitter may result otherwise. |
| RED LED | GREEN LED | Mode |
| Off | On | Normal mode |
| On | On | Waiting to be bound |
| Flashing | On | Signal lost |
| On | Flashing twice | Set failsafe |
CPPM is usable for reducing wirings to some flybar-less controllers, autopilot systems and homebrew UAV systems. Furthermore, it can be used as a wireless trainer system.
Please find the how-to guide with the file named “Set up FrSky as a wireless trainer system” via the following link: www.frsky-rc.com/download.asp?id=23
Recommend Products
Su snippet dinámico se mostrará aquí...
Este mensaje se muestra ya que no brindó ni un filtro ni una plantilla para usar.
To install this Web App in your iPhone/iPad press
and then Add to Home Screen.
